Dimension Calibration

Introduction

  • Gauge Block, Gauge Block Comparator, Long Gauge Block and Gauge Block Micrometer Set, and Ceramic Caliper Checker are used to calibrate Caliper, External Micrometer and Height Gauge
  • ULM Calibration 0 ~ 300 mm (0.0001 (mm), Profile Projector, Microscope, Gauge Block Comparator, Scale and Tape calibrator, Surface Plate, Surface plate Lapping
  • MU Checker are used to calibrate parallelism and flatness of Caliper, External Micrometer and Height Gauge
  • I-checker is used to calibrate Dial Gauge, Dial Test Indicator and Micro-Indicator
  • Universal Length Measuring (ULM) is used to calibrate Standard Rod and Internal Micrometer
  • Profile Projector / Angle Block are used to calibrate Welding Gauge, Angle Protractor, Bevel Protractor Inclinometer, Sine bar
  • Elcometer Precision Foil Set is used to calibrate Coating Thickness Gauge
  • Standard Block Set is used to calibrate Ultrasonic Thickness Gauge

Recognition & Accreditation

Accredited vide NABL Cert No. CC-2457

Our Calibration Capabilities:

• Angle Protractor
• Bevel Protractor / Inclinometer
• Bore Gauge
• Caliper (Dial / Digimatic / Vernier)-0 to 3500mm(0.01mm)
• Coating Thickness Gauge
• Depth Caliper
• Depth Micrometer
• Dial Gauge Indicator up to 150mm(0.01mm)
• Dial Test Indicator up to 3 mm(0.01mm)
• Digital Indicator up to 150mm(0.001mm)
• External Micrometer / Screw Gauge(0 to 1000mm / Res 0.001mm)&0 to     1800 mm(0.01mm)
• Feeler Gauge
• Height Gauge (Dial / Digimatic / Vernier/2D) – up to 1000mm
• Holtest / Three Point Micrometer up to 120mm
• Internal Micrometer / Stick Micrometer
• Laser Distance Meter
• Measuring Tape / Pie Tape
• Pin Gauge
• Plain Plug Gauge / Taper Plug Gauge
• Radius Gauge & Pitch Gauge
• Standard Setting Rod
• Steel Ruler – 0 to 3000 mm
• Surface Profile Gauge
• Thread Plug Gauge / Taper Thread Plug Gauge up to 300mm
• Thickness Foil up to 8 mm
• Ultrasonic Thickness Gauge-Up to 300mm
• Welding Gauge / Weld Fillet Gauge

• Caliper Gauge(Internal / External)
• Test Sieve - 0.020 mm to 120mm
• Lvdt / Electronic Probe with Indicator
• Extensometer
• Roughness Specimen
• Cmm Sphere
• Taper Scale
• Gauge Block (0.5mm to 100mm) & Long Gauge Block -125 to 500 &1000mm
• Surface Table
• Profile Projector / Video Measuring Machine – 300 X 200 mm (0.001mm)
• Universal Length Measuring Machine – 0 to 300mm
• Microscope
• Tape & Scale Calibrator – 0 to 1000 mm
• Gauge Block Comparator –0.5 to 100 mm
• Comparator Stand
• Spirit Level - (0.01mm/m)
• Thread Measuring Wires
• Thickness Gauge(Dial / Digital)
• Snap Gauge / Dial Snap Gauge
• Thread Ring Gauge – M3 to 300 mm
• Plain Ring Gauge up to 300 mm
• Limit Gauges(Linear / Radius / Angle)
• Sine Bar
• Dial Calibration Tester(Dial / Digimatic) – 0 to 25 mm(0.0001mm)
• Try Square / Engineers Square
• Engineers Parallel
• Straight Edge – up to 1500 mm

NorthLab is a Third Party Calibration laboratory based in outskirts of Chennai city (Thiruvallur District). It was established in 2000 as a multi-discipline laboratory by Singapore born NRIs. It presently has a staff strength of over 100 Engineers/ Technicians/Admin Staff.It’s Chennai office is a four storey building with a buildup area of 15000 Sqft.